repo2/common/simulate_atari800xl.sh @ 1475
| 507 | markw | #!/bin/bash
|
|
echo "---------------------------------------------------------"
|
|||
echo "Use 'simulate -run' to skip compilation stage."
|
|||
echo "Use 'simulate -view' to show previous simulation results."
|
|||
echo "---------------------------------------------------------"
|
|||
name=atari800xl
|
|||
. /home/markw/fpga/xilinx/14.7/ISE_DS/settings32.sh
|
|||
mkdir -p sim
|
|||
pushd sim
|
|||
# if we have a WDB file, we can view it if requested (otherwise we remove it)
|
|||
if [ ! -e $name.wdb -o "$1" != "-view" ]; then
|
|||
rm -f $name.wdb
|
|||
# if we have a EXE, we can run it if requested (otherwise we remove it)
|
|||
if [ ! -e $name.exe -o "$1" != "-run" ]; then
|
|||
rm -f $name.exe
|
|||
# copy testbench files
|
|||
cp -p ../tb_atari800xl/* .
|
|||
# copy source files
|
|||
cp ../a8core/atari800xl.vhd .
|
|||
cp ../a8core/pokey*.vhdl .
|
|||
cp ../a8core/antic*.vhdl .
|
|||
cp ../a8core/gtia*.vhdl .
|
|||
cp ../a8core/pia.vhdl .
|
|||
cp ../a8core/cpu* .
|
|||
cp ../a8core/mmu.vhdl .
|
|||
cp ../a8core/irq_glue.vhdl .
|
|||
cp ../a8core/internalromram_simple.vhd .
|
|||
cp ../a8core/os16.vhdl .
|
|||
cp ../a8core/basic.vhdl .
|
|||
cp ../a8core/wide_delay_line.vhdl . #component?
|
|||
cp ../a8core/simple_counter.vhdl . #component?
|
|||
cp ../a8core/reg_file.vhdl . #component?
|
|||
cp ../components/mult_infer.vhdl .
|
|||
cp ../components/generic_ram_infer.vhdl .
|
|||
cp ../components/complete_address_decoder.vhdl .
|
|||
cp ../components/delay_line.vhdl .
|
|||
cp ../components/synchronizer.vhdl .
|
|||
cp ../components/syncreset_enable_divider.vhd .
|
|||
# set up project definition file
|
|||
ls *.vhd* | perl -e 'while (<>){s/(.*)/vhdl work $1/;print $_;}' | cat > $name.prj
|
|||
echo NumericStdNoWarnings = 1 >> xilinxsim.ini
|
|||
# verbose & no multthreading - fallback in case of problems
|
|||
# fuse -v 1 -mt off -incremental -prj %name%.prj -o %name%.exe -t %name%
|
|||
fuse -timeprecision_vhdl 1fs -incremental -prj $name.prj -o $name.exe -t ${name}_tb || exit 1
|
|||
# fuse --mt off -prj %name%.prj -o %name%.exe -t %name%_tb
|
|||
# Check for the EXE again, independent of the errorlevel of fuse...
|
|||
[ -e $name.exe ] || echo "No simulation executable created"
|
|||
fi
|
|||
# Open the iSIM GUI and run the simulation
|
|||
./$name.exe -gui -f ../$name.cmd -wdb $name.wdb -log $name.log -view ../$name.wcfg || exit 1
|
|||
#strace ./$name.exe -gui -f ../$name.cmd -wdb $name.wdb -log $name.log -view ../$name.wcfg >& out
|
|||
#./$name.exe -h -log $name.log
|
|||
else
|
|||
# Only start the viewer on an existing wave configuration (from an old simulation)
|
|||
isimgui -view ../$name.wcfg || exit 1
|
|||
fi
|
|||
popd
|