repo2/replay/simulate.sh
| 1 | markw | #!/bin/bash
|
|
echo "---------------------------------------------------------"
|
|||
echo "Use 'simulate -run' to skip compilation stage."
|
|||
echo "Use 'simulate -view' to show previous simulation results."
|
|||
echo "---------------------------------------------------------"
|
|||
name=Replay
|
|||
| 18 | markw | REPLAY_BASE=/home/markw/fpga/svn/replay/src/hw/replay/cores/replay_lib/
|
|
| 1 | markw | ||
| 18 | markw | . /home/markw/fpga/xilinx/14.7/ISE_DS/settings64.sh
|
|
| 1 | markw | ||
mkdir -p sim
|
|||
pushd sim
|
|||
# if we have a WDB file, we can view it if requested (otherwise we remove it)
|
|||
if [ ! -e $name.wdb -o "$1" != "-view" ]; then
|
|||
rm -f $name.wdb
|
|||
# if we have a EXE, we can run it if requested (otherwise we remove it)
|
|||
if [ ! -e $name.exe -o "$1" != "-run" ]; then
|
|||
rm -f $name.exe
|
|||
# copy testbench files
|
|||
cp -p ../tb/Replay_tb.vhd .
|
|||
| 18 | markw | cp -p ${REPLAY_BASE}/tb/ddr.v .
|
|
cp -p ${REPLAY_BASE}/tb/ddr_parameters.vh .
|
|||
cp -p ${REPLAY_BASE}/tb/Replay_I2C_CH7301.vhd .
|
|||
| 1 | markw | ||
# copy source files
|
|||
| 18 | markw | cp -p ${REPLAY_BASE}/rtl/*.vhd .
|
|
| 1 | markw | cp -p ../source/*.vhd .
|
|
cp -p ../source/*.vhdl .
|
|||
| 18 | markw | cp -p ../../common/a8core/*.vhd .
|
|
cp -p ../../common/a8core/*.vhdl .
|
|||
cp -p ../../common/components/*.vhd .
|
|||
cp -p ../../common/components/*.vhdl .
|
|||
| 1 | markw | ||
# set up project definition file
|
|||
xilperl -p -e 's/^(.+)/vhdl work $1/;' ../$name.prj > $name.prj
|
|||
cat ../${name}_tb.prj >> $name.prj
|
|||
# verbose & no multthreading - fallback in case of problems
|
|||
# fuse -v 1 -mt off -incremental -prj %name%.prj -o %name%.exe -t %name%
|
|||
fuse -timeprecision_vhdl 1fs -incremental -prj $name.prj -o $name.exe -t ${name}_tb || exit 1
|
|||
# fuse --mt off -prj %name%.prj -o %name%.exe -t %name%_tb
|
|||
# Check for the EXE again, independent of the errorlevel of fuse...
|
|||
[ -e $name.exe ] || echo "No simulation executable created"
|
|||
fi
|
|||
# Open the iSIM GUI and run the simulation
|
|||
./$name.exe -gui -f ../$name.cmd -wdb $name.wdb -log $name.log -view ../$name.wcfg || exit 1
|
|||
else
|
|||
# Only start the viewer on an existing wave configuration (from an old simulation)
|
|||
isimgui -view ../$name.wcfg || exit 1
|
|||
fi
|
|||
popd
|